DIY Paper Wall Lamp

by DIY Maven

DIY Paper Wall Lamp

Instructables is featuring this Paper Wall Lamp by naedhi, who used everyday materials, such as sketchbook paper, stapler, scissors and Elmer’s glue, to construct it. The lights themselves are the very versatile LED rope variety, which produce very little heat, making the project not only beautiful but non-flammable too. (Good to know.)

Continue Reading

Make a Paper Towel Dispenser for Your Workspace or Craftroom.

by Chris Gardner

I've eliminated wasteful use of paper towels in nearly every aspect of my life- except in a few instances when working on projects...if anyone has a better way to clean up oil-based stains or epoxy spills, please let me know.

So, one the rare occassions that they're necessary, they might as well look sharp and be available, so I built this paper towel dispenser. I used wood from my scrap bin, so it didn't cost me anything, but it could definately be built for under $12.

Make a Paper Towel Dispenser for Your Workspace or Craftroom.

Materials
    1/2” plywood (2’x4’ is more than enough)
    3/16” hardboard 6”x14”
    1” dowel, at least 27” in length
    Wood glue
    Several bar clamps
    8 3/4” screws
    1” Spade bit
    Jigsaw or bandsaw
    Electric drill
    Sandpaper or electric sander
    Table saw or circular saw (optional)
    Dado blade or router and 1/2” strait bit (optional)
   
1. Cut, or have cut, your plywood to the following sizes. Save excess to make dividers, if desired. I used a scrap piece of white oak, which is a total mystery to me, because oak doesn’t particularly suit my tastes, and I have no idea how it ended up in my sheetgoods storage.

    6x22” (x2)
    4 1/2 x 6” (x4)
    1/2 x 14” (x2)


2. Optional steps:
A. If you have the capability and the desire, run a 1/2” rabbet, 1/4” deep, on the short sides of the face pieces, those 3 1/2” x 14”. If you’d like to make divider shelves, cut a 1/2” dado at equal intervals for the joint (mine were 5 and 4” from the ends). 
B. If you want to recess the hardboard shelf, cut a 3/16” groove (two passes with the table saw (well, a pass and a half-kerf pass) 3 1/2” down on the back of all the face pieces. You’ll then make the hardboard 6” x 13 1/2” to compensate.

3. To make the dowel brackets, drill a 1” hole with it’s center 1 1/4” from the top.  Mark cut lines on the outside edge to the top edge of the bracket.  Use a jigsaw or bandsaw (or even a handsaw) to cut along the lines.


4. Assembly. Glue the four dowel brackets to the inside of the long pieces (see photo). Attach with (2) 3/4” screws. Attach the shelf 3 1/2” from the top, and glue on the face pieces. Insert any dividers, glue, clamp, and allow to dry.

5. Cut the 1” dowel to (2) 13” lengths.

6. Sand the edges to a fine grit, and stain as you please. Be sure to stain the dowels as well.

7. Add the paper towel rolls (which you’ll use sparingly) and fill the top caddy.

8. To hang from the wall, use some heavy duty picture hangers or a cleat system for portability.

 

**Note: My amiga built a similar project, from which I was inspired. She said she built it a few years ago with plans from a magazine, but no longer has the information. If anyone has a reference, please let me know so I can cite it. Cheers.
 

Continue Reading

How to Antique Paper

by DIY Maven

How to Antique Paper

I saw Martha "antique" paper a few years ago, and although I don’t remember her technique, I do remember that it was complicated. I played around with the general idea, though, and came up with an easy way to get the same aged look.

Supplies You'll Need for Aging Paper

 

  • A piece of paper you want to age. (I used regular 24lb laser paper. Of course, print your poem, passage of writing, and etc. to the page before you attempt to...

Continue Reading